Practical Taxidermy Part 16

M, scapula; N, humerus; O, radius; P, ulna;

Q, carpal and meta-carpal bones, and phalanges, of digits, of manes or fore-foot;

R, dorsal and sternal ribs.

THE art of setting up quadrupeds in a natural and life-like manner is of so recent a date that few, if any, of the manuals on taxidermy do more than glance at it. True, they nearly all give directions, in an off-hand way, as to the skinning of mammals; but their instructions are so vague and meagre that, though confessing that the subject is no easy one to write upon, I yet feel that we may, perhaps, improve, in point of detail, on what has gone before.

In accordance with my usual custom, I have procured an animal--a fox--to ill.u.s.trate my instructions, and, the learner having got out the whole of the knives (previously figured) and the whetstone, may proceed to work in the following manner:

Measure the fox, as a preliminary, taking note of his length, breadth, and fineness of limb; length and thickness of muzzle and side of face; and, having aided the recollection by the use of the callipers, and made all necessary notes, lay him on the skinning table, back downwards, and, separating the fur on the stomach at about two inches from the root of the tail, gently insert the point of the skinning knife (keeping the handle well down) under the skin, and continue the cut to within about ten inches of the chest, between the fore limbs--that is to say, up to the first rib, which may be felt with the finger and thumb. If an ordinary-sized fox, this will allow the cut to be of about the same length, viz, ten inches. Be very careful, in making this incision, to cut the top skin only, and not that which retains the bowels.

Having done this, commence to clear away the skin from the flesh on one side by using the point of the knife in a slanting manner between skin and flesh. The fox being with its head from you and directly to your front, the side which you naturally begin on first would be the one on your left; turn the fox now so that its head comes to your left hand instead of directly to your front, and skin in the same manner on the other side, which is now from you. The skin of a fox being very thin about this part, as indeed, nearly all over its body, you must be careful while making your cuts to release the skin, not to push the point of your knife through. As you get along the side of the fox, use your knife, point downward, cutting edge toward you, on the inner side, and from you on the outer, with a sc.r.a.ping motion to separate the skin from the body at the sides.

No doubt, by this time you will be somewhat troubled with a discharge of blood; if so, use sawdust or silver sand, either of which will not dirty the skin, but yet affords a good grip. (Plaster is very commonly used instead of either, but, though a capital absorbent of blood and grease, I object to it, except in the instances of white or very light coloured furs.) Silver sand is, I think, the best of all, as sawdust is apt to get into some furs, and it requires a great deal of pains to get it out again.

By a little management of the point of the knife, and by undercutting slightly, you expose the thighs of the hind limbs. The fox lies still in front of you with its head to your left. Changing your position, go to the tail, and, seizing the foot nearest to you with your right hand, and the skin with your left, push and pull at one and the same time until you expose the knee-joint, or rather--to speak more correctly--the articulation of the "femur" or thigh bone (i, Plate III.) with the two smaller bones ("fibula" and "tibia") which form the shank (K and J).

Let go with your right hand, and by an arrangement of the fingers of the left--difficult to describe--retain your hold of both the skin and flesh of the leg, and re-commence skinning with the knife on each side of the leg until you arrive at the hollow which lies behind, just above the shank; this exposes daylight between skin and flesh, and thus you may get your fingers between the two skins, and, finding the articulation, or joint of the thigh (just mentioned), you push the point of your knife in, and sever the ligaments, and then return the loose shank to its skin.

Holding the fingers of your left hand underneath the skin--thumb and bottom of the palm of the hand opposing--skin out the rest of the thigh, which brings you just on top of the root of the tail. Turn the fox in an exactly opposite direction, and repeat the process; you will before doing this find yourself, perhaps, restrained by the skin of the ventral orifice, which carefully cut out; this frees the limb considerably. (I may mention that the animal skinner must not be afraid of handling his subject; it is not so pleasant nor so delicate an operation as skinning a bird, and, consequently, does not require so fine a touch.)

You will now have exposed the tail at its back and front. Now double up the fox, supporting it with your left hand, and get the whole of the tail free at the root. Letting it rest on the table again, you skin as far up the tail as you can go. The two thighs and part of the back are entirely freed from the skin, but the tail still holds at about three inches up.

Now get a pair of common pincers, such as are used for pulling nails out, and place them so that the tail comes between their hollows; push this against the part still unskinned; hold this firmly down on the table with the left hand, and pull from the root of the tail with the right. Very often the tail will not move past this point; in that case there is nothing left but to cut it off at the root, and place the latter firmly in a vice (after the animal is skinned out), and taking both hands to the skin, cross the thumbs and two first fingers, so as to obtain a good grip and yet prevent the skin of the tail from turning inside out, and pull with all your might (jerking it at the same time) until it slides.

Now free the skin from the back, working round to the front. During this operation the fox must be frequently turned to get round the sides and back. The knife being held short in the hand and guided near the tip by the fore-finger considerably facilitates this. Endeavour as much as possible to keep all the flesh and fat (if any) on the body, and not on the skin.

Coming up now to the fore limbs you will find the skin hold considerably between them at the chest. This is the place where an amateur generally runs his knife through, which, I need hardly say, is one of the worst places in which this accident could happen. Having released the chest, skin all away from the back and shoulder; the fore-arm now appears, showing the articulation of the humerus with the radius and ulna. Skin all round it until you come to the return of the fore-arm in precisely the same manner as you have done with the hind limbs. This point is not so easy to find as is that of the hind legs, but if you will twist the leg you will at once see the point of junction, where slip the knife in and cut off as before. Turn the fox, and treat the other leg in the same manner.

Arrived at the neck, skin all round until you arrive at the base of the skull; you will then become aware of two cartilaginous bodies standing up one on each side--these are the ears. Having skinned a little on top of these, with your finger and thumb raise them slightly and cut them away from their attachment at their bases.

Having freed both ears carefully, skin on the top of the head and the side of the face, until, at about two and a half inches from the ear, and in a line with it, you find the eye, which holds by a thin membrane at this point; carefully skin on the top until the eyeball shows through, and very carefully free it from its attachment all round, except at its lower angle, i.e, that nearest the nose; do the same with the other. Now skin a little more by the side of the jaw until you find it firmly held by a return angle of skin; there leave it attached. Turning the under jaw exactly uppermost, skin along the bone toward the lip as far as you can get, not, however, entirely relieving it from the jawbone at the side, but only until a thin blue membrane appears, which take care not to cut through; this is inside of the skin which comes between the lower lip and the teeth.

The fox's skin is now held to the body at five points, viz, the lower corners of each eye, two; at each return of the jaw just underneath, two more; and at the point of the junction of the two lower jawbones close to the under lip. Procure a saw and saw the head off, so as to expose the brain. On reaching the flesh under the jaw, slip the knife up between on each side of the jaw, which will have the effect of pulling out the tongue attached to the body; preserve the tongue for further operations. With a small chopper, or a mallet and chisel, cut away part of the bone by the palate, between which and the skull bones the brains are included. This considerably a.s.sists the removal of the brain.

A large quant.i.ty of flesh still remains at the top of the head, which must be cleanly removed, and the eyeb.a.l.l.s taken out. You will then find just underneath the eye a bony ridge, running backward to the base of the skull. Surrounding this is a pad of flesh, which hides the attachment of the lower jaw with the upper. By digging underneath with the point of the knife you remove all this flesh, taking care, however, not to cut the attachments of the skin close by, which you previously left, nor the ligaments which hold the upper to the lower jaw. Both sides being served in the same manner, the skull presents a tolerably clean appearance.

The ears are now nearest to the operator. (You will recollect they have been cut off inside). All you can see of them, however, are two shapeless ma.s.ses of gristle surrounding a small hole. On the sides of each--farthest from the head--you must begin cautiously skinning, and by pus.h.i.+ng your left hand through the aperture of the skin of the body, a.s.sist this with your finger and thumb, pushed into the ear from the outside, until by skilfully working with the knife and left-hand fingers you turn the inside skin of each ear to its very edge and tip, until, in fact, each stands up inside the skin, completely reversed.

The next thing which engages your attention is the near fore leg, which you skin as far as you can go, in this instance to the next joint, the one above the carpus or wrist joint. Repeat this with all the limbs, in each case removing all the flesh from the two bones (the radius and ulna of the fore limbs and the tibia and fibula of the hind), which together form those parts of the bones you leave in. If not done previously, now is the time to remove the tail bone. Finally, rub every part of the skin on its inside, as also all the bones left in, with the preservative recommended for mammals (No. 9), not forgetting to push some up the hollow of the brush where the tail bone has been.

Turn your fox's skin completely inside out, skull, leg bones and all, until it comes to its normal position. Commence now from the pad of each foot, and make an incision from near the toes to the point where you left off. Skin round carefully and as much underneath as possible, so as to expose all the flesh and sinews, which clear from off the bone. Be sure to push your knife well round on the top of the bones, which you may do by feeling with the knife and keeping the pad uppermost. This is for the purpose of freeing the attachment of skin around, to prevent ultimate shrivelling.

You may get nearly to the points of the toes in this manner, the only places it should hold to the bone being the top of the last joint and at the tips of the toes; the actual pad, which you will find loaded with a thick fat, must be trimmed as well as possible.

Whilst doing all this take notice of the points of attachment and shapes of sinews, etc, which you remove, especially those of the hind legs.

It will be recollected that although we have returned the head, nothing has been done to the upper lip or nose from the outside.

Accordingly the knife must be slipped the whole way round, beginning at the nose and keeping as close to the teeth as possible, in fact, on the very edges of the gums. This is important. Skin away now from the bone of the upper jaw on each side; having bared this, come back to the nose, the cartilage of which skin until you arrive at the extreme tip; in point of fact, skin it entirely out, which is best done by cutting a portion off inside, and then carefully skinning the little bit which is left until the extreme tip of the nostrils is arrived at.

This requires great care, as the black skin on the top of the nose is extremely thin. This is the very worst place in which a cut could be made; and, although the cutting out of the nose could be done in five minutes, the tyro will do well if he completes it in half an hour.

This being satisfactorily ended, free the flesh from the bone, except at the attachment previously left at the corner of the eye. There is now a smooth and s.h.i.+ny skin between the upper lip and the cut you made to free it from the gums; this is the inner skin of the lips; the knife must, therefore, be slipped between this skin and the outer skin, and it must then be carefully separated the whole of the way round, to the extreme edge of the upper lip; this requires nice manipulation and great care. This inner skin now hangs down from the inner lip, and forms a bag, the uses of which will be seen hereafter.

There still remains the inside of the bone of the nose to be cleaned out with a pointed knife. The lower lip is now attached only at the extreme tip; this must be cut away from the gum at that place and the knife pushed underneath, by the side of the canine teeth, to still further free the skin.

The skin is now ready for stuffing, when you have thoroughly rubbed the preservative into the cut of the pads, and around the eyelids, outside the ears, mouth, nose, and vent, or any damaged parts. If the skin is allowed to remain for a night as it is, it will be all the better, as it allows time for the preservative to penetrate. Throw the tongue into a pickle of tannin and carbolic acid (see chapter IV, No.

15), and there leave it until wanted.

It will no doubt have been observed that I have used several tools not previously mentioned as necessaries; my reason is that I a.s.sume no one who aspires to become an amateur workman fails to provide himself with such everyday implements as saw, chisel, chopper, hammer, pincers, rule, etc, the only tool not in ordinary use being the "callipers,"

which are made of various patterns, and are used to take measurements of breadths and depths in situations where the foot rule is useless, such as spherical and cylindrical bodies. The price of a pair of callipers need not exceed 1s.

When the skin is sufficiently penetrated with the preservative, lay it on its back ready for stuffing. First take hold of the bone of the nose and push the skull into the skin, so that it comes through the orifice of the skin of the body. The back of the skull being now toward you, proceed to push tow into the cavity whence the brains were removed, also in the cavity of each orbit, between the articulations of the jaws at the sides of the face, and the lower jaw--in fact, everywhere where the flesh has been removed, forming it as well as you possibly can to the shape which existed previously.

When you have modelled this as well as the nature of the tow will allow, return the head through the skin to its first position. Next cut four strong wires of suitable size, one a little stronger than the others and somewhat longer than the whole of your skin, including brush. Point this wire at one end and make two loops in it (each similar to that in Fig. 1); one loop to occur about 4 in. from the tail, and the other up in the chest, near the junction of the fore limbs. Spread a sufficient quant.i.ty of tow inside the skin to run all the way along the back and up the neck to join the head. Enter the point of the wire through the orifice of the skin, push it up the lower jaw into the hollow part of the skull, and holding the head in the left hand, calculate so that the wire may come through the skin at about the centre of the head, about 1.5 in. from, and above each eye.

Bear in mind that the skull being somewhat thick, it is the more necessary for your wire to have cutting edges, as before explained.

Having pushed the wire through three or four inches, cut off the point with your large pliers (Fig. 16) to prevent injuring yourself, turning down the remainder to prevent the wire pulling through again. Push the other end of the wire right up the brush, to do which you must bend it back on itself about halfway up, straightening up as you proceed.

Next take four wires, somewhat longer than the legs, and pointed at each end. Push one of these right up the foot in at the pad, along the back of the leg, and up into the body, pus.h.i.+ng it through its proper loop on the body wire, and twisting it round and round the same with your pliers until it is firmly attached. Fill the cut pad with chopped tow, and nicely sew it up to its normal shape. Do the same with the three remaining limbs. You should be able now to lift the fox by any one of the leg wires, and find it support the remainder.

Having by this time determined the shape which the fox shall a.s.sume--that is to say, if standing, running, or springing on its prey--commence by gradually filling up the neck with suitable pieces of tow, bending the head and neck as you wish; in point of fact, shaping as you go on. Next work down the chest, and then fill up the skin of the limbs with smaller pieces of tow, endeavouring to keep to the characteristic shapes of the thin and thick parts (various stuffing irons of different degrees of thickness will have to be used during the process). Having filled up the fore limbs, bend them to their required position and go to the hind, disregarding the body for the present.

The hind limbs have more character in them than the fore, and are, in consequence, harder to model; be the more careful, therefore, to pay particular attention to the proper development of these limbs, bending them into shape during work, and keeping the thighs nice and thin, and distinct from the body. All the limbs being shaped, model up the various parts of the body, not getting it like a sack, as is too frequently the case, but producing those fine flowing lines which are so necessary to ensure the perfect model of a zoological specimen.

Lift your work up from time to time, noting where inequalities appear.

The fox being now fairly well shaped, sew it up with a three-cornered skin (or glover's) needle and string. A board is now to be procured, of the necessary length and thickness, in which holes are to be bored to receive the leg wires, which are then clenched underneath. This operation, no doubt, will knock the specimen somewhat out of shape, which, of course, is easily remedied, and having brought up the limbs to their proper position, you will now address yourself to the formation of the head and face.

This latter will possess but little expression, owing to the nose, etc, being cut out. To remedy this procure a cork, which push into the cavity whence the cartilage of the nose has been removed, roughly shaping it, and covering it over with a pad of putty, pus.h.i.+ng some also into the skin of the nostrils at the same time. The inner skin of the lips is still hanging down as a bag. Fill this up with sufficient putty to allow for shrinking, sewing it to the outer skin.

The lips may now be adjusted in position by sewing the upper to the under, if the fox is to be shown with a closed mouth, or by driving in "needle points" in various positions, if the mouth is to be open, until these parts set. Fill in the orbits with putty, attending to the eyebrows, reproducing the various muscles underneath, and insert the artificial eyes. All that now remains to be done is to push two pointed wires down the back of the ears, and run them along each edge, finally pus.h.i.+ng them in the skin of the head, where required; the two loose ends being twisted together at the top keep the ears in position.

The tongue, if intended to be shown, must be removed from the pickle, cut on its under side, and skinned completely out to the tips and to each edge. All the included flesh must then be cut away, and replaced with putty, the cut sewn up, and it is then ready to be inserted in the mouth in the required position, when modelled into shape.

The animal being stuffed and mounted to your satisfaction, you must bear in mind, that although you have perfectly cured the skin--turning it, in fact, into a species of leather--you have not rendered it proof against the attacks of insects; it must, therefore, be washed over with one of the preparations given in Chapter IV.

The preceding method of skinning and stuffing an animal is given, not because it is the most scientific, but because it is the most satisfactory to the learner, and is, indeed, the method which obtains with the majority of taxidermists. Though perfectly efficient as far as it goes, it yet possesses the disadvantage of allowing a certain percentage of shrinkage, and that caused solely by the yielding nature of the tow used to fill out the places where the muscles formerly rested. To an educated eye this defect is at once recognised by the uneven contour of the cheeks, superciliary muscles, and various parts of the limbs, and also by the generally "wooden" appearance of the specimen.

The system on which I will now give a lesson is far more tedious in its application, but certain in its effects, being, in fact, subst.i.tuting hard for loose stuffing, and differing from the foregoing in one essential particular, viz, the modelling of the head and limbs with a medium of an unyielding nature. To ill.u.s.trate this, we will take another fox or similar animal. After skinning it, as in the foregoing lesson, you will, instead of leaving the leg bones in the skin, cut them completely out down to the claws, which may best be done by skinning down as far as you can, cutting the bones off at the last joint, then making an incision above the pads, and slipping the bones completely out; this allows you to work right down to the last joint of the phalanges or toes, at which point you cut the bones free.

The head is now to be considered. When it has been cut off as before, skin down to the eyelids, and instead of leaving them attached at the lower angles, cut them completely away. Now take the skin off all round the skull, until the return of the skin of the side of the mouth is arrived at. Skin well under the jaw to the very tip, and now begin under-cutting at the sides, coming up to the return angle--keeping, however, well to the side of the skin. By cautious working you can skin in between the inner and outer skins until you can touch the tips of the lower teeth at the point of the jaw with your fingers.

Coming along from here by the side of the lower jaw, you skin by undercutting almost to the inside of the mouth, taking care not to cut the thin membrane which holds at the extreme edge. Still working along the lower jaw, come right up until you can cut out, just under the eye, the top end of the return. Leaving it attached by a thin membrane 'to the upper jaw, skin downward toward the nose, and, by undercutting and using great care, completely skin up to the nostril, which sever.

Do precisely the same with the other side. The nostrils being completely skinned out, the skin holds just below them.

Place the head on the table, standing on the base of its skull, the ears toward you. Take the nostrils with the finger and thumb of the left hand, and with the knife (the broad knife will be found most useful here) very carefully work all round until you arrive at the extreme tip of the inner skin of the upper jaw, which is now turned inside out, and actually rests below the under jaw. Your cuts must be made a hair's breadth at a time to get to the extreme edge. By this time the severed nostrils will have fallen some little distance underneath the under jaw. See, now, that the lips, both upper and lower, as well as the inner angles of the mouth, are skinned inside to the extreme edge at every point, or all your labour will be thrown away. This operation is one of the most nice and difficult in the whole range of skinning operations, and is equally difficult to describe. Cut out the cartilage of the nose, slip out the tongue, and generally trim the head in the usual manner, and well rub in the preservative. If you should find too much of the inner angle left far up in the mouth it may be cut off.

If the head were returned now it would be seen that the lower edges of the inside skin of the mouth were the only points of attachment, and even there only to the edge of the teeth all around them.