Getting Gold: A Practical Treatise for Prospectors, Miners and Students Part 14

SLUICE PLATES

I am indebted to Mr. F. W. Drake for the following account of sluice plates, which I have never tried, but think the device worth attention:

"An addition has been made to the gold-saving appliances by the placing of what are called in America, 'sluice plates' below the ordinary table.

The pulp now flows over an amalgamating surface, 14 ft. long by 4 ft.

wide, sloping 1 1/2 in. to the foot, and is then contracted into a copper-plated sluice 15 ft. long by 14 in. wide, having a fall of 1 in.

to the foot. Our mill manager (Mr. G. C. Knapp) advocated these sluice plates for a long time before I would consent to a trial. I contended that as we got little or no amalgam from the lower end of our table plates there was no gold going away capable of being recovered by copper plates; and even if it were, narrow sluice plates were a step in the wrong direction. If anything the amalgamating surface should be widened to give the particles of gold a better chance to settle. His argument was that the conditions should be changed; by narrowing the stream and giving it less fall, gold, which was incapable of amalgamation on the wide plates, would be saved. We finally put one in, and it proved so successful that we now have one at the end of each table. The per-centage recovered on the sluice plates, of the total yield, varies, and has been as follows:--October, 9.1 per cent; November, 6.9 per cent; December, 6.4 per cent; January, 4.3 per cent; February, 9.3 per cent."

MEASURING INACCESSIBLE DISTANCES

To ascertain the width of a difficult gorge, a deep river, or treacherous swamp without crossing and measuring, sight a conspicuous object at the edge of the bank on the farther side; then as nearly opposite and square as possible plant a stake about five feet high, walk along the nearer margin to what you guess to be half the distance across (exact.i.tude in this respect is not material to the result), there plant another stake, and continuing in a straight line put in a third. The stakes must be equal distances apart and as nearly as possible at a right angle to the first line. Now, carrying in hand a fourth stake, strike a line inland at right angles to the base and as soon as sighting over the fourth stake, you can get the fourth and second stakes and the object on the opposite sh.o.r.e in line your problem is complete. The distance between No. 4 and No. 3 stakes is the same as that between No.

1 and the opposite bank.

TO SET OUT A RIGHT ANGLE WITH A TAPE

Measure 40 ft. on the line to which you wish to run at right angles, and put pegs at A and B; then, with the end of the tape held carefully at A, take 80 ft., and have the 80 ft. mark held at B. Take the 50 ft. mark and pull from A and B until the tape lies straight and even, you will then have the point C perpendicular to AB. Continue straight lines by sighting over two sticks in the well-known way.

_Another method_.--Stick a pin in each corner of a square board, and look diagonally across them, first in the direction of the line to which you wish to run at right angles, and then for the new line sight across the other two pins.

A SIMPLE LEVELLING INSTRUMENT

Fasten a common carpenter's square in a slit to the top of a stake by means of a screw, and then tie a plumb-line at the angle so that it may hang along the short arm, when the plumb-line hangs vertically and sights may be taken over it. A carpenter's spirit-level set on an adjustable stand will do as well. The other arm will then be a level.

Another very simple, but effective, device for finding a level line is by means of a triangle of wood made of half-inch boards from 9 to 12 ft. long. To make the legs level, set the triangle up on fairly level ground, suspend a plummet from the top and mark on the cross-piece where the line touches it. Then reverse the triangle, end for end, exactly, and mark the new line the plumb-line makes. Now make a new mark exactly half way between the two, and when the plumb-line coincides with this, the two legs are standing on level ground. For short water races this is a very handy method of laying out a level line.

TO MEASURE THE HEIGHT OF A STANDING TREE

Take a stake about your own height, and walking from the b.u.t.t of the tree to what you judge to be the height of the timber portion you want, drive your stake into the ground till the top is level with your eyes; now lie straight out on your back, placing your feet against the stake, and sight a point on the tree. AB equals BC. If BC is, say 40 ft., that will be the height of your "stick of timber." Thus, much labour may be saved in felling trees the timber portion of which may afterwards be found to be too short for your purpose.

LEVELLING BY ANEROID BAROMETER

This should be used more for ascertaining relatively large differences in alt.i.tudes than for purposes where any great nicety is required.

For hills under 2000 ft., the following rule will give a very close approximation, and is easily remembered, because 55 degrees, the a.s.sumed temperature, agrees with 55 degrees, the significant figures in the 55,000 factor, while the fractional correction contains _two fours_.

Observe the alt.i.tudes and also the temperatures on the Fahrenheit thermometer at top and bottom respectively, of the hill, and take the mean between them. Let B represent the mean alt.i.tude and b the mean temperature. Then 55000 X B - b/B + b = height of the hill in feet for the temperature of 55 degrees. Add 1/440 of this result for every degree the mean temperature exceeds 55 degrees; or subtract as much for every degree below 55 degrees.

TO DETERMINE HEIGHTS OF OBJECTS

_By Shadows_

Set up vertically a stick of known length, and measure the length of its shadow upon a horizontal or other plane; measure also the length of the shadow thrown by the object whose height is required. Then it will be:--As the length of the stick's shadow is to the length of the stick itself, so is the length of the shadow of the object to the object's height.

_By Reflection_

Place a vessel of water upon the ground and recede from it until you see the top of the object reflected from the surface of the water. Then it will be:--As your horizontal distance from the point of reflection is to the height of your eye above the reflecting surface, so is the horizontal distance of the foot of the object from the vessel to its alt.i.tude above the said surface.

_Instrumentally_

Read the vertical angle, and multiply its natural tangent by the distance between instrument and foot of object; the result is the height.

When much accuracy is not required vertical angles can be measured by means of a quadrant of simple construction. The arc AB is a quadrant, graduated in degrees from B to A; C, the point from which the plummet P is suspended, being the centre of the quadrant.

_When_ the sights AC are directed towards any object, S, the degrees in the arc, BP, are the measure of the angle of elevation, SAD, of the object.

TO FIND THE DEPTH OF A SHAFT

_Rule_:--Square the number of seconds a stone takes to reach the bottom and multiply by 16.

Thus, if a stone takes 5 seconds to fall to the bottom of a shaft--

5 squared = 25; and 25 X 16 = 400 feet, the required depth of shaft.

DESCRIPTION OF PLAN FOR RE-USING WATER

Where water is scarce it may be necessary to use it repeatedly. In a case of this kind in Egypt, the Arab miners have adopted an ingenious method which may be adapted to almost any set of conditions. At a is a sump or water-pit; b is an inclined plane on which the mineral is washed and whence the water escapes into a tank c; d is a conduit for taking the water back to a; e is a conduit or lever pump for raising the water. A certain amount of filtration could easily be managed during the pa.s.sage from c to a.

COOLING COMPOUND FOR HEATED BEARINGS

Mercurial ointment mixed with black cylinder oil and applied every quarter of an hour, or as often as expedient. The following is also recommended as a good cooling compound for heavy bearings:--Tallow 2 lb., plumbage 6 oz., sugar of lead 4 oz. Melt the tallow with gentle heat and add the other ingredients, stirring until cold.

CLEANING GREASY PLUMMER BLOCKS

When, through carelessness or unpreventable cause, plummer blocks and other detachable portions of machinery become clogged with sticky deposits of grease and impurities, a simple mode of cleansing the same is to take about 1000 parts by weight of boiling water, to which add about 10 or 15 parts of ordinary was.h.i.+ng soda. Keep the water on the boil and place therein the portions of the machine that are to be cleaned; this treatment has the effect of quickly loosening all grease, oil, and dirt, after which the metal is thoroughly washed and dried. The action of the lye is to form with the grease a soap soluble in water. To prevent lubricating oil hardening upon the parts of the machinery when in use, add a third part of kerosene.

AN EXCELLENT ANTI-FRICTION COMPOUND

For use on cams and stamper shanks, which will be harmless should it drop into the mortar or stamper boxes, is graphite (black-lead) and soft soap. When the guides are wooden, the soft soap need not be added; black-lead made into a paste with water will act admirably.

TO CLEAN BRa.s.s

Oxalic acid 1 oz., rotten stone 6 oz., powdered gum arabic 1/2 oz., sweet oil 1 oz. Rub on with a piece of rag.

A SOLVENT FOR RUST

It is often very difficult, and sometimes impossible, to remove rust from articles made of iron. Those which are very thickly coated are most easily cleaned by being immersed in a nearly saturated solution of chloride of tin. The length of time they remain in this bath is determined by the thickness of the coating of rust. Generally from twelve to twenty-four hours is long enough.

TO PROTECT IRON AND STEEL FROM RUST

The following method is but little known, although it deserves preference over many others. Add 7 oz. of quicklime to 1 3/4 pints of cold water. Let the mixture stand until the supernatant fluid is entirely clear. Then pour this off, and mix with it enough olive oil to form a thick cream, or rather to the consistency of melted and re-congealed b.u.t.ter. Grease the articles of iron or steel with this compound, and then wrap them up in paper, or if this cannot be done, apply the mixture somewhat more thickly.

TO KEEP MACHINERY FROM RUSTING

Take 1 oz. of camphor, dissolve it in 1 lb. of melted lard; mix with it (after removing the sc.u.m) as much fine black-lead as will give it an iron colour; clean the machinery, and smear it with this mixture. After twenty-four hours rub off and clean with soft, linen cloth. This mixture will keep machinery clean for months under ordinary circ.u.mstances.

FIRE-LUTE

An excellent fire-lute is made of eight parts sharp sand, two parts good clay, and one part horse-dung; mix and temper like mortar.