The Scholfield Wool-Carding Machines Part 1

The Scholfield Wool-Carding Machines.

by Grace L. Rogers.

THE SCHOLFIELD WOOL-CARDING MACHINES

_First to appear among the inventions that sparked the industrial revolution in textile making was the flying shuttle, then various devices to spin thread and yarn, and lastly machines to card the raw fibers so they could be spun and woven. Carding is thus the important first step. For processing short-length wool fibers its mechanization proved most difficult to achieve._

_To the United States in 1793 came John and Arthur Scholfield, bringing with them the knowledge of how to build a successful wool-carding machine. From this contribution to the technology of our then infant country developed another new industry._

THE AUTHOR: _Grace L. Rogers is curator of textiles, Museum of History and Technology, in the Smithsonian Inst.i.tution's United States National Museum._

Carding is the necessary preliminary step by which individual short fibers of wool or cotton are separated and cleaned of foreign materials so they can be spun into yarn. The thoroughness of the carding determines the quality of the yarn, while the position in which the carded fibers are laid determines its type. The fibers are laid parallel in order to spin a smooth compact yarn, or they are crossed and intermingled to produce a soft bulky yarn.

Primitive Carding

The earliest method of carding wool was probably one in which, by use of the fingers alone, the tufts were pulled apart, the foreign particles loosened and extracted, and the fibers blended. Fuller's teasels (thistles with hooked points, _Dispasacus fullonum_), now better known for raising the nap on woven woolens, were also used at a very early date for carding. The teasels were mounted on a pair of small rectangular frames with handles; and from this device developed the familiar small hand card (see fig. 2), measuring about 8 inches by 5 inches, in which card clothing (wire teeth embedded in leather) was mounted on a board with the wire teeth bent and angled toward the handle. The wool was placed on one card and a second card was dragged across it, the two hands pulling away from each other. This action separated the fibers and laid them parallel to the handle, in a thin film. After the fibers had been carded in this way several times, the cards were turned so that the handles were together and once again they were pulled across each other. With the wire teeth now angled in the same direction, the action rolled the carded fibers into a sliver (a loose roll of untwisted fibers) that was the length of the hand card and about the diameter of the finger. This placed the wool fibers crosswise in relation to the length of the sliver, their best position for spinning.[1] Until the mid-18th century hand cards were the only type of implement available for carding.

[Ill.u.s.tration: Figure 2.--HAND CARDS "USED ON PLANTATION OF MARY C.

PURVIS," NELSON COUNTY, VIRGINIA, during early 1800's and now in U.S.

National Museum (_cat. no._ T2848; _Smithsonian photo_ 37258).]

[Ill.u.s.tration: Figure 3.--THE FIRST MACHINE IN LEWIS PAUL'S BRITISH PATENT 636, ISSUED AUGUST 30, 1748. The treadle moved the card-covered board _B1_, in a horizontal direction as necessary to perform the carding operation. With the aid of the needlestick the fibers were removed separately from each of the 16 cards _N_. The carded fibers were placed on a narrow cloth band, which unrolled from the small cylinder _G_, on the left, and was rolled up with the fibers on the cylinder _I_, at the right.]

First Mechanical Cards

The earliest mechanical device for carding fibers was invented by Lewis Paul in England in 1738 but not patented until August 30, 1748. The patent described two machines. The first, and less important, machine consisted of 16 narrow cards mounted on a board; a single card held in the hand performed the actual carding operation (see fig. 3). The second machine utilized a horizontal cylinder covered with parallel rows of card clothing. Under the cylinder was a concave frame lined with similar card clothing. As the cylinder was turned, the cards on it worked against those on the concave frame, separating and straightening the fibers (see fig. 4). After the fibers were carded, the concave section was lowered and the fibers were stripped off by hand with a needle stick, an implement resembling a comb with very fine needlelike metal teeth. Though his machine was far from perfect. Lewis Paul had invented the carding cylinder working with stationary cards and the stripping comb.

[Ill.u.s.tration: Figure 4.--THE PATENT DESCRIPTION OF PAUL'S SECOND MACHINE suggested that the fibers be carded by a cylinder action, but be removed in the same manner as directed in the first patent.]

[Ill.u.s.tration: Figure 5.--ILl.u.s.tRATIONS FROM BRITISH PATENT 628, ISSUED JANUARY 20, 1748, to Daniel Bourn for a roller card machine.]

[Ill.u.s.tration: Figure 6.--THE MOST IMPORTANT SINGLE FEATURE Ill.u.s.trated in Richard Arkwright's British patent 1111 of December 16, 1775, provided "a crank and a frame of iron with teeth" to remove the carded fibers from the cylinder.]

Another important British patent was granted in 1748 to Daniel Bourn, who invented a machine with four carding rollers set close together, the first of the roller-card type (see fig. 5). To produce a practical carding machine, however, several additional mechanical improvements were necessary. The first of these did not appear until more than two decades later, in 1772, when John Lees of Manchester is reported to have invented a machine featuring "a perpetual revolving cloth, called a feeder," that fed the fibers into the machine.[2] Shortly afterward, the stripper rollers[3] and the doffer comb[4] (a mechanical utilization of Paul's hand device) were added. Both James Hargreaves and Richard Arkwright claimed to be the inventor of these improvements, but it was Arkwright who, in 1775, first patented these ideas. His comb and crank (see fig. 6) provided a mechanical means by which the carded fibers could be removed from the cylinder. With this, the cylinder card became a practical machine. Arkwright continued the modification of the doffing end by drawing the carded fibers through a funnel and then pa.s.sing them through two rollers. This produced a continuous sliver, a narrow ribbon of fibers ready to be spun into yarn. However, it was soon realized that the bulk characteristic desired in woolen yarns (but not desired in the compact types such as worsted yarns or cotton yarns) required that the wool be carded in a machine that would help produce this.

[Ill.u.s.tration: Figure 7.--NEWBURYPORT, Ma.s.sACHUSETTS, in 1796, AN ENGRAVING FROM JOHN J. CURRIER'S _History of Newburyport, Ma.s.sachusetts_, 1764-1909, vol. 2, Newburyport, 1906-09.]

In carding wool it was found more effective to omit the flat stationary cards and to use only rollers to work the fibers. The method of preparing the sliver also had to be changed. Since it was necessary to remove the wool fibers crosswise in the sliver, a fluted wooden cylinder called a roller-bowl was used in conjunction with an under board or sh.e.l.l. As a given section of the carded wool was fed between the fluted cylinder and the board, the action of the cylinder rolled the fibers into a sliver about the diameter of the finger and the length of the cylinder. Although these were only 24-inch lengths as compared to the continuous sliver produced by the Arkwright cotton-carding machine,[5]

wool could still be carded with much more speed and thoroughness than with the small hand cards. This then was the state of mechanical wool carding in England in the 1790's as two experienced wool manufacturers, John and Arthur Scholfield, planned their trip to America.

John and Arthur Scholfield

The Scholfields, however, were not to be the first to introduce mechanical wool carding into America. Several attempts had been made prior to their arrival. In East Hartford, Connecticut, "about 1770 Elisha Pitkin had built a mill on the east side of Main Street near the old meeting-house and Hockanum Bridge, which was run by water-power, supplied by damming the Hockanum River. Here, beside grinding grain and plaster, was set up the first wool-carding machine in the state, and, it is believed, in the country."[6] Samual Mayall in Boston, about 1788 or 1789, set up a carding machine operated by horse power. In 1791 he moved to Gray, Maine, where he operated a shop for wool carding and cloth dressing.[7] Of the machines used at the Hartford Woolen Manufactory, organized in 1788, a viewer reported he saw "two carding-engines, working by water, of a very inferior construction." They were further described as having "two large center cylinders in each, with two doffers, and only two working cylinders, of the breadth of bare sixteen inches, said to be invented by some person there."[8] But these were isolated examples; most of the woolen mills of this period were like the one built in 1792 by John Manning in Ipswich, Ma.s.sachusetts, where all the work of carding, spinning, and weaving was still performed by hand.

The Scholfields' knowledge of mechanical wool-processing was to find a welcome reception in this young nation now struggling for economic independence. The exact reason for their decision to embark for America is unknown. However, it may well be that they, like Samuel Slater[9]

some three years earlier, had learned of the bounties being offered by several state legislatures for the successful introduction of new textile machines.

Both John and Arthur were experienced in the manufacture of woolens.

They were the sons of a clothier (during the 18th century, a person who performed the several operations in finis.h.i.+ng cloth) and had been apprenticed to the trade. Arthur was 36 and a bachelor; John, a little younger, was married and had six children. Arthur and John, with his family, sailed from Liverpool in March 1793 and arrived in Boston some two months later. Upon arrival, their immediate concern was to find a dwelling place for John's family. Finally they were accommodated by Jedediah Morse, well-known author of _Morse's geography and gazetteer_, in a lodging in Charlestown, near Bunker Hill. In less than a month John began to build a spinning jenny and a hand loom, and soon the Scholfields started to produce woolen cloth. The two brothers were joined in the venture by John Shaw, a spinner and weaver who had migrated from England with them. Morse, being much impressed with some of the broadcloth they produced, was especially interested to find that John and Arthur understood the actual construction of the textile machines. Morse immediately recommended the Scholfields to some wealthy persons of Newburyport (see fig. 7), who were interested in sponsoring a new textile mill.

[Ill.u.s.tration: Figure 8.--CROSS-SECTION OF A SCHOLFIELD WOOL-CARDING MACHINE. The wool was fed into the machine from a moving ap.r.o.n, locked in by a pair of rollers, and pa.s.sed from the taker-in roller to the angle stripper. This latter roller transferred the wool on to the main cylinder and acted as a stripper for the first worker roller. After pa.s.sing through two more workers and strippers, the wool was prepared for leaving the main cylinder by the fancy, a roller with longer wire teeth set to reach into the card clothing of the large cylinder. Then the doffer roller picked up the carded fibers from the main cylinder in 4-inch widths the length of the roller. These sections were freed by the comb plate, pa.s.sed between the fluted wooden cylinder and an under board, where they were converted into slivers, and deposited into a small wooden trough.]

The Newburyport Woolen Manufactory

A Newburyport philanthropist, Timothy Dexter, contributed the use of his stable. There, beginning in December 1793, the Scholfields built a 24-inch, single-cylinder, wool-carding machine. They completed it early in 1794, the first Scholfield wool-carding machine in America. The group was so impressed that they organized the Newburyport Woolen Manufactory.

Arthur was hired as overseer of the carding and John as overseer of the weaving and also as company agent for the purchase of raw wool. A site was chosen on the Parker River in Byfield Parish, Newbury, where a building 100 feet long, about half as wide, and three stories high was constructed. To the new factory were moved the first carding machine, two double-carding machines, as well as spinning, weaving and fulling machines. The carding machines were built by Messrs. Standring, Armstrong, and Guppy, under the Scholfields' immediate direction. All the machinery with the exception of the looms was run by water-power; the weaving was done by hand. The enterprise was in full operation by 1795.

John and Arthur Scholfield (and John's 11-year-old son, James) worked at the Byfield factory for several years. During a wool-buying trip to Connecticut in 1798, John observed a valuable water-power site at the mouth of the Oxoboxo River, in the town (i.e., towns.h.i.+p) of Montville, Connecticut. Here, the brothers decided, would be a good place to set up their own mill, and on April 19, 1799, they signed a 14-year lease for the water site, a dwelling house, a shop, and 17 acres of land. As soon as arrangements could be completed, Arthur, John, and the latter's family left for Montville.

[Ill.u.s.tration: Figure 9.--IN THE COLLECTION OF THE HENRY FORD MUSEUM, DEARBORN, MICHIGAN, IS THIS ORIGINAL SCHOLFIELD WOOL-CARDING MACHINE of the early 19th century. (_Photo courtesy of the Henry Ford Museum._)]

The Scholfields quite probably did not take any of the textile machinery from the Byfield factory with them to Connecticut--first because the machines were built while the brothers were under hire and so were the property of the sponsors, and second because their knowledge of how to build the machines would have made it unnecessary to incur the inconvenience and expense of transporting machines the hundred odd miles to Montville. However, John Scholfield's sons reported[10] that they had taken a carding engine with them when they moved to Connecticut in 1799 and had later transferred it to a factory in Stonington. The sons claimed that the frame, cylinders, and lags of the machine were made of mahogany and that it had originally been imported from England. However, it would have been most uncommon for a textile machine, even an English one, to have been constructed of mahogany; and having built successful carding machines, the men at Byfield would have found it unnecessary to attempt the virtually impossible feat of importing an English one. If it ever existed and was taken to Connecticut, therefore, this machine was probably not a carding machine manufactured by the Scholfields. It is more probable that the first Scholfield carding machine remained in the Byfield mill as the property of the Newburyport Woolen Manufactory.

[Ill.u.s.tration: Figure 10.--AN ORIGINAL SCHOLFIELD WOOL-CARDING MACHINE AT OLD STURBRIDGE VILLAGE, STURBRIDGE, Ma.s.sACHUSETTS. It is now run by electricity. (_Photo courtesy of Old Sturbridge Village._)]

During the next half century, this mill was held by a number of individuals. William Bartlett and Moses Brown, two of the leading stockholders of the company, sold it in 1804 to John Lees, the English overseer who succeeded the Scholfields, and he continued to operate it for about 20 years. On August 24, 1824, the mill was purchased at a Sheriff's sale by Gorham Parsons, who sold a part interest to Paul Moody, a machinist from the textile town of Lowell. Moody operated the mill for the next 5 years and at his death in 1831 his heirs sold their interest back to Parsons. In 1832 it was leased for 7 years by William N. Cleveland and Solomon Wilde under the name of William N. Cleveland & Co. Following the expiration of the lease in 1839, a portion of the mill was occupied for 3 or 4 years by Enoch Pearson, believed to have been a descendant of the John Pearson who had been a clothier in Rowley in 1643, and subsequently various industries occupied other portions and later the entire building, which burned with all its contents on October 29, 1859.

If the first Scholfield carding machine remained a part of the property, therefore it must have been lost in that fire. However, the Scholfields'

importance to American wool manufacture was not contingent on the building of one successful carding machine, regardless of whether it was the first. It was the change in the scope of their business ventures after their move to Connecticut that synonymized the name of Scholfield with mechanical wool carding in America.

John and Arthur had built their woolen mill at Uncasville, a village in the town of Montville, and there Arthur remained with his brother until 1801, when he married, sold his interest to John, and moved to Pittsfield, Ma.s.sachusetts. John and his sons continued to operate the mill until 1806, when difficulties over water privileges spurred him to purchase property in Stonington, Connecticut, where he built a new mill containing two double-cylinder carding machines.[11] In 1813, leaving one son in charge at Stonington, John returned to Montville and purchased another factory and water privileges. He continued in the woolen manufacture until his death in 1820.

Arthur, soon after arriving in Pittsfield, constructed a carding machine and opened a Pittsfield mill. The following advertis.e.m.e.nt appeared in the _Pittsfield Sun_, November 2, 1801:

Arthur Scholfield respectfully informs the inhabitants of Pittsfield and the neighboring towns, that he has a carding-machine half a mile west of the meeting-house, where they may have their wool carded into rolls for 12-1/2 cents per pound; mixed 15-1/2 cents per pound. If they find the grease, and pick and grease it, it will be 10 cents per pound, and 12-1/2 cents mixed. They are requested to send their wool in sheets as they will serve to bind up the rolls when done. Also a small amount of woolens for sale.

The people around Pittsfield soon realized that the mechanically carded wool was not only much easier to spin but enabled them to produce twice as much yarn from the same amount of wool. Although many brought their wool to be carded at his factory, Arthur was not without problems. These were evident in his advertis.e.m.e.nt of May 1802, in which he stated that if the wool was not properly "sorted, clipped, and cleansed" he would charge an extra penny per pound. He also added that he would issue no credit. Shortly after this, recognizing the need for additional carding machines in other localities, Arthur Scholfield undertook the work of manufacturing such machines for sale. Through this venture he was to spread his knowledge of mechanical wool carding throughout the country.

The Scholfield Machines

The first record of Arthur's sale of carding machines appeared in the _Pittsfield Sun_ in September 1803. The next year, in May 1804, his advertis.e.m.e.nt informed the readers that A. Scholfield continued to card wool, and also that:

He has carding-machines for sale, built under his immediate inspection, upon a new and improved plan, which he is determined to sell on the most liberal terms, and will give drafts and other instructions to those who wish to build for themselves; and cautions all whom it may concern to beware how they are imposed upon by uninformed speculating companies, who demand more than twice as much for machines as they are really worth.

Scholfield must have felt that some of his compet.i.tors were charging much more for their carding machines than they were worth. Also, others were producing inferior machines that did not card the wool properly.

Both factors encouraged Arthur to continue the commercial production of wool-carding machines. In April 1805 he again advertised:

Good news for farmers, only eight cents per pound for picking, greasing, and carding white wool, and twelve and a half cents for mixed. For sale, Double Carding-machines, upon a new and improved plan, good and cheap.

And in 1806:

Double carding machines, made and sold by A. Scholfield for $253 each, without the cards, or $400 including the cards. Picking machines at $30 each. Wool carded on the same terms as last year, viz.: eight cents per pound for white, and twelve and a half cents for mixed, no credit given.